Powertek Logo
UK Office:
US Office:

AC-DC Watt Transducer, Models WT1ph and WT3ph, measure all waveform types from sinewaves, on/off dutycycle to complex VFD applications, DC, 1Hz-50kHz

The WT3ph WX3ph Power Analysing Transducers measures single phase 1ph and three phase 3ph and AC/DC Power safely converting to a voltage, current loop output, RS485, Modbus or Profibus interface

Data sheet Get a quote

Supplied with Din Rail mounting kit

Product Specifications

    Functionality
  • Measures Watts, VARs, VA, PF, Vrms, Vpk, Vcf, Arms, Apk, Acf, Freq and Ainrush
  • Measures 3 phase totals: Sum HP, Sum Watts, Sum VARs, Sum VA, Sum PF
  • Accurate with all waveshapes or load types: DC and variable frequency AC
  • Frequency from 1Hz to 5000Hz fundamentals, bandwidth DC-50kHz
  • Measures continuous and Burst Type, pulsing loads and waveforms
  • Available input ranges from 2V to 600V ac or dc from 10%-125% of range
  • Analog Outputs x3, isolated: 0-5V, 0-10V, 4-20mA: assigned to any measurement like kW or kVAr
  • Fast response time 1mS, Auto or manual scaling
  • Rated working voltage insulation 1.5kVpk, flash tested 2.5kV for 1 minute
  • Screw terminal input/output connections with terminals covers
  • Auxiliary power input 12/24/48/110/230 Vdc or Vac
    • Approvals and Environment
  • Certified accuracy Class 0.2%, 0.5% or 1.0% at +23°C ±5°C, traceable to NIST/NPL
  • Working temperature range 0°C - 50°C / Functional temp range –10°C - 70°C
  • CE Marked, FCC and UL Compliant
  • UL94V0, IEC1010 cat II, IEC348, DIN 57411
  • Case IP50, terminals IP30 complies with IEC529
    • Connectivity
  • HMI options for local set-up and display
  • Modbus TCP/IP (over Ethernet)
  • Supplied with LV Modbus Test Panel for Windows and Master-Slave configurations
  • NI Labview Driver support
  • Interface via WiFi Bridge to mobile devices, Profibus, ProfiNet and RS485

Health and Safety, good working practices when using Watt Transducers

  • Ensure that all personnel connecting and configuring the WT3ph are trained with electric shock and fire hazards associated with electricity supplies
  • Ensure the circuit under test is switched off and isolated before connection or configuration
  • Only use fused safety type cables for connections to the WT3ph probe. All connections should be insulated to prevent human contact
  • Ensure that the WT3ph output (lo terminal) is connected to a grounded point on the DCS/data logger/measurement system
  • Ensure that the maximum differential input voltage of (1500Vpk) and input voltage to ground (1500Vpk) are not exceeded
  • Users should work in pairs, both parties should be trained and familiar with medical procedures in the event of electric shock
  • Ensure the circuit test is protected with over current protection
  • During installation, avoid all mechanical stress to the WT3ph terminals
  • Do not use if the WT3ph case is open or damaged
  • Ensure that the storage and operating conditions are clean and dry

    • Description

    Unlike most Watt Transducers, our Model WT Series uses high-speed simultaneous sampling with analog-to-digital converters, these provide accurate ac measurements regardless of waveshape or frequency. This includes real power (W), real power factor (PF) reactive power (VAr) delivered to a load. Bi-directional capability means power can be measured in both directions, with indication of import and export. Especially in applications like Locomotive, Electric vehicle where motoring and regeneration occurs with power and energy. Models are available in a variety of configurations with current ranges up to 1000A and nominal voltage ratings up to 600V. Models are available in 1, 2 and 3 element versions; suitable for all single-phase and three-phase power systems. RS485, CAN BUS, Modbus and Analog output signals are available. Forward (consumed) power is indicated with a positive polarity and reverse (generated) power with a negative polarity. Unidirectional outputs (4-20mA) indicate forward (consumed) power, 4-12-20mA allow for both directions. Easy scaling of VTs and CTs is possible. All outputs are galvanically isolated from the measured inputs and instrument power.

    The sensor power input is designed to operate over a wide range associated with process control and sub-station auxiliary dc supply systems.  Some typical applications are voltage monitoring in Solar PV, Dc drives, UPS, Frequency Changers, Process Control, Rail Transportation, and EV. For all products, a NIST/NPL/UKAS traceable calibration certificates of conformance are available.

    WT1ph Watt Transducer order codes

    WT1ph / Voltage range / Current range / Scaling / output type / instrument power

    WT3ph / Wiring / Voltage range / Current range (mV) / Scaling / analog outputs+type / instrument power

    eg WT3ph / 4W / 400V / 500mV / Scaling / Anlg / MBus / 220Vac

    WX-3ph / Voltage range / Current range / Scaling / output type / instrument power


    Order code examples:

    WT1ph / 120V / 500A-CT / 500:5 / Std / 4-20 / 24Vdc
    120Vac input, 500/5A input, CT type 500:5, 4-20mA output with 24Vdc aux power input

    Powertek specializes in the design and manufacture of electrical power, voltage and current measuring instrumentation
    Contact Powertek today