IRF Series clip-on split core current probe

The IRF series ruggedized current probes all utilize a flexible clip on current sense coil, allowing fast and safe installation, ideal for current monitoring in hostile arc-furness and smelting environments.
Models from 100Apk to 120,000Apk, optional 0-5V, 4-20mA, 1A or 5A output with Arms conversion. Wide Bandwidth up to 1MHz, to accommodate complex waveshapes, IP65 robust enclosure

IRF-RMS AC Transducer rms input to dc output

10kV rated compact sense coil fits in small spaces
Models from 100A to 120,000A
Works with all current waveshapes
Aperture sizes from 100mm to 2000mm
Basic traceable accuracy <0.2%
Instantaneous and rms converting models
Use with Modbus, SCADA systems and PLCs
Extend measurement range of data loggers and power analyzers

Products

IRF flexible split core current probe
IP65 enclosure to keep out water and contamination

Models Arms/Apk
IRF3 - 450Arms / 600Apk
IRF15 - 2250Arms / 3000Apk
IRF30 - 4500Arms / 6000Apk
IRF60 - 9,000Arms / 12,000Apk
IRF150 - 22,500Arms / 30,000Apk
IRF300 - 45,000Arms / 60,000Apk
IRF600 - 90,000Arms / 120,000Apk

	Peak Current ratings 100Apk to 120,000Apk
	Sensitivity set to give ± 6 volts peak output(e.g. 1.0mV/A for ± 6000A peak ).
	Optional 1A or 5A output
	RMS conversion option with a wide range of outputs: 0-100mV, 0-1V, 0-5V, 0-10V, 0-20mA, 4-20mA and 5-25mA
	Wide Bandwidth 1Hz to 1MHz
	Thin, flexible, clip-around coils (diameter 8.5mm) in lengths of 300, 500, 700, 1000 and 1500mm
	Peak coil voltage isolation 10kV
	Cable length (box to coil) of 2.5m. Optional 4 metres lengths
	+12Vdc, +24Vdc, 110Vac, 230Vac power supply with 1kV isolation
	IP65 robust enclosure
	Low output impedance Min. output loading 10kohm (for rated accuracy)
	CE marked
	Accuracy <1% of reading

TA5V-5A or TA5V-1A output module - used for interfacing IRF & RCT probes to existing CT metering circuits
Casing: Din Rail
Bandwidth: TA5V-1A DC-10kHz TA5V-5A 25Hz-500Hz
Rating: 5VA
Accuracy: 1.0% accuracy
Input impedance: 100kohm
Accurate with waveform crest factors: 1 - 5
Input ranges: 10mV to 10V input
Power: 24Vdc, 110Vac or 230Vac power

Model TA5V-5A 1A or 5Arms output module

cthr01.jpg (30896 bytes)

External CTHrms converter module

IRF-RMS
External RMS converter
Bandwidth: DC-50kHz
Optional ac coupled version
0.5% accuracy
Input impedance 50ohm or 100kohm
Accurate with waveform crest factors: 1 - 5
Input ranges: 2mV to 50V input
Wide range of dc outputs:
0-100mV, 0-1V, 0-5V, 0-10V
0-20mA, 4-20mA and 5-25mA
Power: 12, 24, 48, 110Vdc, 110Vac or 230Vac power

Description

The robust IRF current probes all utilize a flexible clip on current sense coil, allowing fast and safe installation, ideal for current monitoring and retrospective fitting. Using the optional 1A or 5A output, the IRF are a direct replacement for existing current transformer, completely compatible with installed CT circuits.

Many of the current transformer safety considerations can be eliminated using this technique, which produces safe low level signals even with no secondary burden or loading. With frequency bandwidths from 1Hz to 1MHz, the IRF is ideal for single and three phase power systems containing harmonics and distorted waveshapes. Even PWM motor drive signals, chopped and pulsed waveforms can be measured accurately. Using the optional IRF-rms converter, a dc output is produced making the IRF current probe ideal for control or system monitoring purposes. Typically the IRF clip on, clip around flexible coil current probe is used with SCADA systems, PLC, digital storage oscilloscopes, data loggers, power meters and power analyzers.

Datasheets

IRF Current Probe Data Sheet

Powertek specializes in the design and manufacture of electrical power, voltage and current measuring instrumentation
Contact Powertek today