Powertek Logo
UK Office:
US Office:

Our range of Non-Inductive Coaxial Current Shunts

Typical Applications: GaN and High di/dt Signals. Wide Bandwidth Current viewing resistors (CVR)

Co-Axial Current Shunt Models
   From 3.2MHz-2GHz   


Considerations when selecting a Co-axial shunt
Co-axial shunt Data Sheet
coaxial shunts series a Series A
0.001 to 0.2ohms 4-6 watts
series f Series F
0.001 to 0.2ohms 75-300 watts
series k Series K Series
0.0001 to 0.01ohm 150 to 500watts
series l In-line Series L
0.001 to 0.2ohms 4-6 watts
series m Series M
0.001 to 0.1 ohm 20 to 125 watts
series r Series R
0.00015 to 0.01ohm 225-850 watts
series sdn Series SDN
0.001 to 0.5ohm 2-3 watts
series sdn 414 Series SDN-414
0.01 to 0.1ohm 2 watts
series w 1 stud type Series W 1 Stud Type
0.001-2.0 ohms 7.5watts
series w 2 stud type Series W 2 Stud Type
0.001-0.05ohms 12.5-15 watts
series w 4 stud type  Series W 4 Stud Type
0.00025-0.01ohms 15-20watts
series w bar strap Series W Bar Strap
0.0005-0.005ohms 2.5watts
series w clamp type Series W Clamp Type
0.001-0.01ohms 5-7.5 watts
series w flange input 3 5 Series W Flange Input 3.5s
0.0001-0.025ohms 300-21,100 Joules
series w flange input 6 5 Series W Flange Input 6.5s
0.00005-0.01ohms 490-42,200 Joules
series w flange input 12 5 Series W Flange Input 12.5s
0.000025-0.005ohms 980-84,000 Joules

Considerations when selecting a Co-axial shunt
Co-axial shunt Data Sheet

About the Current Viewing Resistor (CVR) / Non-Inductive Co-Axial Shunt Resistors

 

Our range of CVR's are non inductive high frequency coaxial shunts designed to operate over a wide bandwidth, with both AC and DC power systems, especially where phase angle is a consideration, crucial during impedance measurements and power calibration systems. Very useful for adding or extending the current range of Frequency Response Analyzers and Multimeters. CVR's can be used with phase angle meters, where phase angle between voltage-voltage, voltage-current or current-current is required, ideal for phase protection, power meters, wattmeters, energy meters and current transformer calibration.

CVR's are rugged high frequency resistors designed to sustain very high peak power and current inputs generated by capacitor banks, pulse generator systems and steady state current loads. Their linear response over a broad frequency band provides an accurate indication of current magnitude free from inductive components. Inherent in CVR design is a coupling between the major electrical parameters of resistance, bandpass, energy capacity and wattage rating. This means we provide a wide ranging series of standard units covering a broad range of specifications.

 

WATTAGE RATING

Although most CVR's are designed primarily for surge current measurements, their rugged construction and their low temperature coefficient resistive elements have made them ideally suited to a number of steady state applications. An average wattage rating applicable to continuous current loading is thus quoted for each resistor series. Care should be taken in circuitry involving either AC or high duty cycle pulse currents that this rating not be exceeded, since CVR damage by overheating can result. If requested we can supply resistors with special construction which will increase the standard wattage rating to a high value depending on the model.

 

FREQUENCY RESPONSE

Bandpass of a CVR is essentially flat from DC to an upper limit determined primarily by skin effect in the resistive element. Associated bandpass is based on a measured 10% to 90% risetime response to a step function of current produced by a coaxial line pulse generator. The di/dt of the test pulse exceeded 10^12 amps/sec.

 

RESISTANCE VALUES

Unless otherwise specified, resistors are supplied with resistance tolerance of ±4% of nominal value. In addition, a Kelvin Bridge determination of its exact resistance, accurate to ±0.2% is supplied with each unit. The thermal coefficient of the coaxial shunts is 8-10 ppm/degC. A wide range of special resistance values for any of our standard units can be supplied.

 

MECHANICAL DESIGN

Case construction of all coaxial current viewing resistors is silverplated brass. Standard output signal connector is BNC with other connectors available. Large coaxial CVRs utilize a high current flange and coaxial threaded stud input connections. Powertek's flat configuration CVRs, the Series W, originally developed for flat plate transmission line installation, are available in a wide range of unit widths and input configurations and have been found to be particularly useful in applications requiring resistors with extreme energy and wattage ratings.

 

WORLD-WIDE TRACEABILITY

All measurements made using the CVR coaxial shunts are traceable to National and International standards; through the measurement standards of Powertek. All CVR coaxial shunts are supplied with a certificate of conformance necessary for quality assurance standards such as IEC17025/ISO9001. Independent measurement certification is possible using UKAS, A2LA or Z540/NAVLAP certificate.

   

Non inductive coaxial shunt - CVR applications

 
  • Pulsed current applications
  • Calibration laboratories
  • Current sensing for phase meters
  • Single phase angle indicators V-A
  • Three phase phase angle indicators V-A
  • Cos Phi indicators
  • Power factor meters
  • High Frequency Watt Meters
  • Wideband Power meters
  • Power analysis
  • Current transformer calibration
  • Current probe phase delay
  • SCR current measurements
  • Current control of automatic welders
  • Measure output of automotive alternators
  • Fault current detection to determine bearing wear of steam turbine generators
  • Electron Beam Welding
  • Current detection in detonation systems
  • Three-phase fault testing in power transmission substations
  • Fault detection in modulators
  • Measurement of laser system currents
  • IGBT Chopper current control in electric cars
  • Circuit breaker testing